# Sample configuration file for smartd.  See man smartd.conf.

# Home page is: http://smartmontools.sourceforge.net

# $Id: smartd.conf,v 1.33 2004/01/13 16:53:06 ballen4705 Exp $

# smartd will re-read the configuration file if it receives a HUP
# signal

# The file gives a list of devices to monitor using smartd, with one
# device per line. Text after a hash (#) is ignored, and you may use
# spaces and tabs for white space. You may use '\' to continue lines.

# You can usually identify which hard disks are on your system by
# looking in /proc/ide and in /proc/scsi.

# The word DEVICESCAN will cause any remaining lines in this
# configuration file to be ignored: it tells smartd to scan for all
# ATA and SCSI devices.  DEVICESCAN may be followed by any of the
# Directives listed below, which will be applied to all devices that
# are found.  Most users should comment out DEVICESCAN and explicitly
# list the devices that they wish to monitor.
DEVICESCAN

# First (primary) ATA/IDE hard disk.  Monitor all attributes, enable
# automatic online data collection, automatic Attribute autosave, and
# do a short self-test every day at 2am, and a long self test
# Saturdays at 3am.
/dev/hda -a -o on -S on -s (S/../.././02|L/../../6/03)

# Monitor SMART status, ATA Error Log, Self-test log, and track
# changes in all attributes except for attribute 194
/dev/hdb -H -l error -l selftest -t -I 194 

# A very silent check.  Only report SMART health status if it fails
# But send an email in this case
/dev/hdc -H -m admin@example.com

# First two SCSI disks.  This will monitor everything that smartd can
# monitor.  Do extended self-tests Wednesdays at 6pm and Sundays at 1 am
/dev/sda -d scsi -s L/../../3/18
/dev/sdb -d scsi -s L/../../7/01

# Monitor 4 ATA disks connected to a 3ware controller card which uses
# the 3w-xxxx driver. Do a long self-tests Sundays at 1, 2, 3, and 4 am
/dev/sdc -d 3ware,0 -a -s L/../../7/01
/dev/sdc -d 3ware,1 -a -s L/../../7/02
/dev/sdc -d 3ware,2 -a -s L/../../7/03
/dev/sdc -d 3ware,3 -a -s L/../../7/04


# HERE IS A LIST OF DIRECTIVES FOR THIS CONFIGURATION FILE
#   -d TYPE Set the device type: ata, scsi, removable, 3ware,N
#   -T TYPE set the tolerance to one of: normal, permissive
#   -o VAL  Enable/disable automatic offline tests (on/off)
#   -S VAL  Enable/disable attribute autosave (on/off)
#   -n MODE No check. MODE is one of: never, sleep, standby, idle
#   -H      Monitor SMART Health Status, report if failed
#   -l TYPE Monitor SMART log.  Type is one of: error, selftest
#   -f      Monitor for failure of any 'Usage' Attributes
#   -m ADD  Send warning email to ADD for -H, -l error, -l selftest, and -f
#   -M TYPE Modify email warning behavior (see man page)
#   -s REGE Do self-test when type/date matches regular expression (see man page)
#   -p      Report changes in 'Prefailure' Normalized Attributes
#   -u      Report changes in 'Usage' Normalized Attributes
#   -t      Equivalent to -p and -u Directives
#   -r ID   Also report Raw values of Attribute ID with -p, -u or -t
#   -R ID   Track changes in Attribute ID Raw value with -p, -u or -t
#   -i ID   Ignore Attribute ID for -f Directive
#   -I ID   Ignore Attribute ID for -p, -u or -t Directive
#   -v N,ST Modifies labeling of Attribute N (see man page)
#   -a      Default: equivalent to -H -f -t -l error -l selftest
#   -F TYPE Use firmware bug workaround. Type is one of: none, samsung
#   -P TYPE Drive-specific presets: use, ignore, show, showall
#    #      Comment: text after a hash sign is ignored
#    \      Line continuation character
# Attribute ID is a decimal integer 1 <= ID <= 255
# All but -d, -m and -M Directives are only implemented for ATA devices
#
# If the test string DEVICESCAN is the first uncommented text
# then smartd will scan for devices /dev/hd[a-l] and /dev/sd[a-z]
# DEVICESCAN may be followed by any desired Directives.
